Quantcast
Channel: ToManual.com » Search Results » rubber bonnet stopper for peugeot
Viewing all articles
Browse latest Browse all 10

2006 RIDGELINE AIR DEFLECTOR P/N 08P47-SJC-100 Installation Instruction

0
0

Download TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Tape measure Felt-tip pen Shop towel asking tape Clip remover Center bracket 2 Front brackets A 2 Front brackets B 2 Side brackets 6 Plastic grommets 6 Screws, 5 x 13 mm 2 Screws, 6 x 11 mm 7 Protective tapes Air deflector 2 Alcohol pads center stopper AII 28583 All 28583 (0502)
1. Using the front “H” emblem, locate the center of the hood. From the bottom of the hood, measure up 2 in. (52 mm), and clean the area where the center support will attach with one alcohol pad from the kit. 4. Turn over the rubber molding and locate the six square holes in the hood. Push one plastic grommet into each square hole. 5. Clean the front edge of the hood with the other alcohol pad from the kit. INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” NOTE: Be careful not to damage the body finish when you install the air deflector. This air deflector should be installed only when the
ambient air temperature is above 60°F (15°C). 2. Remove the adhesive backing from the center stopper, and attach it to the hood at the marked location with the convex mark facing down. 3. Open the hood. Locate the outer four clips that attach the rubber molding. Remove the four clips from the rubber molding. 4120081H Clean the front edges. HOOD
SQUARE HOLES PLASTIC GROMMETS (6) Clean the front edges. RUBBER Turn over. 4608080H CLIP RUBBER 4D24020H CENTER STOPPER MARKED LOCATION CENTER ADHESIVE BACKING 2 in. (52 mm) “H” EMBLEM HOOD HOOD CENTER STOPPER CONVEX MARK All 28583 (0502) 7. Attach a piece of masking tape to the hood under each bracket. 6. Slide the front rackets A and B and the side brackets over the lip of the hood. Align the hole in each bracket with the hole in the plastic grommet. 8. Using a felt-tip pen, mark the masking tape at the center of each bracket. Remove all of the brackets from the hood. 9. Attach six protective tapes around the front edge of the hood at the six outboard marked locations. 10. Attach the remaining protective tape around the center front edge of the hood. Remove the masking tapes. 4120110H MASKING TAPE FELT-TIP PEN MARK FRONT A/ FRONT B/ SIDE BRACKET 4120121H CENTER PROTECTIVE TAPE RUBBER Turn up. PROTECTIVE TAPE PROTECTIVE TAPE 4D24030H FRONT BRACKET A HOLE (6) SIDE BRACKET SIDE BRACKET FRONT BRACKET B FRONT BRACKET B RUBBER Turn over. All 28583 (0502) 13. Close the hood. Position the air deflector on the hood, and attach the air deflector to the two front brackets A, two front brackets B and center bracket using the five clips A.Check that the edges of the moldings are flat and not tucked under. 4608090H CLIP B RUBBER 12. Install the center bracket over the hood around the protective tape. Push the center bracket against the hood while you install the screw. 4120131H Push against the hood. BRACKETS HOOD RUBBER Turn over. 5 x 13 mm SCREWS FRONT BRACKETS A (2) SIDE BRACKET FRONT BRACKETS B (2) CENTER BRACKET SIDE BRACKET 11. Reinstall the two front brackets A, two front brackets B and two side brackets over the hood around the protective tapes, and install the 5x13mm screws. Push each bracket against the hood while you install the screw. Do not tighten the six 5 x 13 mm screws at this time. 4D24040H
6 x 11 mm SCREW AIR DEFLECTOR 6 x 11 mm SCREW COLLAR COLLAR FRONT BRACKET A CLIPS A (5) CENTER BRACKET SIDE BRACKET FRONT BRACKET B INCORRECT OK AIR DEFLECTOR AIR DEFLECTOR MOLDING HOOD HOOD MOLDING 14. ligning the holes in the air deflector over the two side brackets, install the two 6 x 11 mm screws and two collars, and then tighten the screws securely. 15. Open the hood, and tighten the six 5x13mm screws you installed in step 11. 16. install the four clips B to secure the rubber molding.


Viewing all articles
Browse latest Browse all 10

Latest Images

Trending Articles





Latest Images